How To Remove Picture Hooks From Wall

Download Commodity

Download Article

Hooks can be used to hang almost anything from your wall as long as they aren't too heavy. When you want to create actress hanging space in your home, you tin employ adhesive hooks for lighter materials, similar picture frames or calendars. If you lot want to back up larger items, such as mirrors or artwork, you may accept to mount your hooks to the studs behind your walls. Yet, if you lot aren't using a stud or your wall is made of drywall, masonry, or concrete, you lot'll demand to use a wall anchor to go the well-nigh support.

1
Utilise a stud finder to locate studs behind your walls. Studs are the framework behind the walls in your home, and screwing into them offers the most support for your hooks. Stud finders are pocket-size handheld machines that can detect the wood behind your walls. Agree the stud finder confronting the wall and press the button to turn information technology on. Move the stud finder across your wall and expect for it to beep. Marking the location of your stud on the wall with a pencil and so you know where to put your hook.^[1]
- Studs are commonly 16 inches (41 cm) autonomously from ane some other, but your home's architecture may be different.
- If you lot don't take a stud finder, yous tin can also try knocking on your walls. Knocking on a stud will produce a full, solid sound while knocking on an area without one will sound hollow.^[two]
two
Drill a hole into your wall slightly smaller than the screw your hook came with. Change your drill bit then it's slightly smaller than the threaded part of your spiral. Place the end of your drill on the mark you fabricated on your wall and start running the drill slowly to get-go your hole. One time you drill through the wall, speed upward the drill so it tin can dig into the wooden stud. Brand your hole the same depth as your spiral so information technology can agree securely.^[iii]
- You lot don't have to pre-drill holes if you lot don't want to, merely it can prevent your walls from chipping and your studs from splitting.
- Don't pre-drill holes if your hook uses nails to hold it in place.
Advertizement
iii
Feed the screw into the hole on your claw and line it up to the wall. Your hook should have a hole in its front to secure your screw. Identify your screw through the hole and concur the hook upwards to your wall. Place the bespeak of your screw in the hole you simply drilled and so you tin can easily start screwing it in.^[4]
- If the hook uses nails, slide the end of the nail through the pigsty and identify the end of the nail confronting the mark you drew on the wall.
- Many hooks will come with the screws or hardware required to secure them to the wall.
- Information technology's okay to allow the hook hang crooked when you first place information technology on the wall since you can rotate it after yous tighten it.
4
Screw or hammer the claw into the wall. If your hook uses nails, use a hammer to drive the smash into the stud. Otherwise, use a screwdriver to tighten the claw onto your wall. Brand sure your hook faces right-side up before completely securing the screw so it hangs correctly.^[5]
- Check your hook'due south maximum weight before hanging anything on it so you don't accidentally rip it out of the wall.
Tip: Use your drill with a screwdriver bit to secure your hook in identify faster.

Advertisement

one
Get wall anchors for your screws. Wall anchors look like hollow screws and are used in physical, masonry, or drywall when you don't take a stud to support your claw. Look for a wall ballast meant to support the weight of the object y'all're hanging and made for the textile your wall is fabricated from. Make certain you take plenty wall anchors for all of your screws.^[half-dozen] ^[7]
- Wall anchors can be purchased from your local hardware store.
- Avoid hanging anything betwixt studs without wall anchors since they could rip out of the wall and fall out.
2
Drill a hole the aforementioned size as your wall ballast. Match the width of your wall anchor to the drill bit you use to make the hole. Start drilling slowly to protect your drill bit and reduce the amount of dust. Go along drilling your hole until it'due south the aforementioned depth as your anchor.^[eight]
- Since drilling into a hard surface can create dust, wear safety glasses and a confront mask while you're drilling.
Tip: If you're securing your claw in drywall, employ an awl or the stop of your screwdriver to pierce a hole in the wall without creating any dust.^[9]
3

Screw or feed your ballast into the hole yous made. If your anchor doesn't have threading on the outside, only slide the anchor into place and tap it in with a hammer if you demand to. If your anchor is threaded, utilise your screwdriver to secure it to your wall. Make certain the stop of the anchor is flush with the wall when you're finished.^[10]
iv
Identify your screw into the claw and align it with the anchor on your wall. Locate the hole on the front of your claw where the spiral feeds in. Slide the threaded finish of your screw through the hole and set the point of the spiral within the anchor.
- You lot hook should come with the screws needed to concur it in place. If non, use a screw that'due south the same length as your ballast.
- Information technology doesn't matter if your screw hangs crooked when you start screwing it in since Yous'll have a chance to rotate it afterwards.
v
Secure the screw in the center of your anchor. Utilize your screwdriver to tighten the screw into the anchor. As the spiral goes further into the ballast, the ballast will expand and create a firm grip so it doesn't fall out of the wall. When the hook is almost tight against the wall, make certain information technology's rotated the right direction so yous can hang things on it.^[eleven]
- Y'all may too use a drill with a screwdriver bit to work faster.
Advertisement

1
Slide the back off of the hook. Adhesive hooks usually have a backplate that can be removed to make installation easier. Flip the adhesive claw upside downwards and endeavour sliding the back slice downwardly to remove it from the hook. Once the hook piece is separated from the backplate, set the hook aside.^[12]
- Agglutinative hooks can be purchased from your local convenience shop.
- Smaller adhesive hooks may non have a removable back. If your hooks do not, you can skip this step.
Tip: Agglutinative hooks can be large for hanging clothes or heavier objects, or they could be pocket-size to hang pictures. Cull the style hook that works best for what you're trying to hang.
2
Skin the backing from the agglutinative strip and press it onto the backplate. Adhesive strips volition come with your packet of hooks and should be double-sided. Locate the side of the adhesive strip meant to attach to the backplate and skin the protective layer off. Firmly press the adhesive strip onto the flat side of the backplate so the tab points down. Hold the strip on the backplate for 30 seconds to ensure information technology'due south fully adhered.^[13]
- If your hook doesn't have a removable backplate, and so printing the strip directly on the back side of the hook.
iii
Press the adhesive strip onto your wall and agree it for 30 seconds. Remove the protective backing on the second side of the adhesive strip. Align the backplate on your wall where y'all want to place the hook and brand sure the tab on the front of the backplate is at the bottom. Press the adhesive strip for 30 seconds so it bonds tightly to your wall.^[14]
- Most adhesive hooks should stick to any wall surface that's more often than not flat.
four
Slide the hook onto the wall and wait 1 hour earlier hanging annihilation. Agree the hook piece over the backplate then the tab lines up with the pigsty in front of the hook. Slide the hook down onto the backplate until the tab clicks into identify to secure your hook. Leave the claw empty for at least one hour then the adhesive has fourth dimension to fully fix.^[15]
- Don't hang annihilation more 5 lb (2.3 kg) on large agglutinative hooks since they could break off of the wall. If yous have smaller hooks, read the instructions advisedly to come across how much weight they can support.^[sixteen]
Advertisement

Enquire a Question

200 characters left

Include your email accost to get a message when this question is answered.

Submit

Advertizing

VideoRead Video Transcript

Make sure to purchase hooks that support the weight of the object y'all want to hang.
Use 2 hooks if yous want to distribute the weight evenly and put less stress on your wall.

Don't use hooks with nails if your walls are fabricated of concrete or masonry, or if yous're securing the hook in drywall without a stud.

Things You'll Need

Stud finder
Pencil
Drill
Screws
Hooks
Screwdriver or hammer

Drill
Rubber spectacles
Face up mask
Screwdriver
Wall anchors
Screws
Hooks

Adhesive hooks

Almost This Commodity

Commodity Summary 10

The easiest way to install a hook in the wall is to anchor it between studs. To exercise this, you'll need a wall ballast, which looks like a hollow screw. Anchors help support your hooks to brand sure your hook doesn't autumn out of the wall. Once you lot take your anchor, drill a pigsty into the wall that's the same depth equally your ballast. So, feed your ballast into the hole you fabricated past borer it with a hammer or screwing information technology in. Finally, place your hook in the ballast and tighten information technology with a screwdriver. Make sure your hook is rotated in the correct direction! Alternatively, if you don't take a drill, buy adhesive hooks rated for the weight of the object y'all desire to hang. For more tips, including how to mount your hook in a wooden stud, read on!

Did this summary help yous?

Thank you to all authors for creating a page that has been read 41,490 times.

Did this article help you?